Bottom Brackets

- Enables the use of a MegaEVO (30mm spindle) crankset on a 68mm English threaded frame - Compatible with Gravity Gradient MegaEVO 30mm cranks

- Spindle Interface Type: 386 EVO - BB Shell Width: 68mm - Bottom Bracket Shell I.D.: 46mm - BB/Frame Interface: T47 - Weight: 95g

There's precious little that's better than a fresh bottom bracket. This complete FSA BB30 Bottom Bracket contains 2 stainless steel bearings, 2 C-Clips, 2 dust covers, and 1 adjustment washer.

ISIS revolutionized bottom bracket spindles. Keep yours spinning smoothly with this Platinum ISIS Bottom Bracket from FSA. - Forged, hollow chromoly spindle with titanium nitride coating - Integrated, large ball bearing design - Cold-forged aluminum cups - Includes crank bolts

Features three sealed cartridge bearings. - Fits Daytona, Racing Triple, Centaur, Veloce and Mirage, 1193 and later Athena and pre-1995 Record and Chorus - 115mm spindle recommended for triple cranks and 32 or 35mm seat tubes - Unique taper is not compatible with Shimano - Weight: 233 grams

The Hellbender70 bottom bracket utilizes a bearing made of 440C stainless steel, providing exceptional ride quality and reliability. The stainless steel bearing in the Hellbender 70 strikes a perfect balance between value and lasting performance. - 440C stainless steel bearings, dual lip seal, marine grease - Machined aluminum cups

Running a conventional threaded bottom bracket on your BB30 or PF30 frame doesn't have to be complicated. This press-fit adapter from FSA goes in snug and opens up a lot of crankset possibilities for your BB30/PF30 frame. - Aluminum - Allows conventional threaded bottom brackets to be installed in a BB30 or PF30 frame - Install with headset press (not included) and green Loctite (included)

FSA PowerPro JIS Cartridge Bottom Brackets. - Includes bolts - Spindle Interface Type: Square Taper JIS - BB Shell Width (mm): 68 - BB/Frame Interface: English

Shimano BB-ES300 Octalink V2 Bottom Brackets - Fits Shimano Octalink V2 Spline Cranksets - Crankarm fixing bolts not included

- Simple and reliable square taper bottom bracket - Replaces both BB-UN26 and BB-UN55 - Sealed cartridge bearings - Cr-Mo axle - For bicycles equipped with a chain case, select BB-UN300-K - For E-type front derailleur compatibility, choose BB-UN300-E - Fixing bolts not included; Shimano FC-E6000 bolts suggested

- Deore-level BB92 press-fit Hollowtech II bottom bracket - Compatible with all mountain Hollowtech II cranks

A variant of the external bottom bracket, PressFit cut weight by up to 40 grams and provide easier installation by allowing you to press the bearing cups into the frame instead of threading them. There's no change to the crank — spindle length and diameter remain the same. - BB Shell Width (mm): 104.5 mm , 107 mm

- Adapters press directly into specific PF30, BB30, BB86 or BBright frames and allow the use of standard Ultra-Torque (UT) crank sets and EPS components - Updated design increases surface area contact with the frame's bottom bracket, reducing the possibility of noise from frames with slight imperfections - Ultra-Torque OS Fit BB-cup tool is required for adapter installation

Surly OD Bottom Brackets - Compatible with 24mm spindles - Moonlander BB fits a 100mm bottom bracket shell, but exterior width conforms to BB121 standard

The SRAM DUB bottom bracket series has a simple job—to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Designed for use with SRAM Wide Cranksets - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard

The new SRAM DUB bottom bracket series has a simple job—connect your crankarms and protect the smooth, long-lasting application of power to your drivetrain. To allow that singular focus, we’ve engineered the DUB spindle to be the one true unifying component. One oversized spindle to work across every bottom bracket standard. For better crankarm compatibility. For better protection from the elements. For longer-lasting performance. To be stronger, smoother, simpler. Now, back to the ride. - One oversized spindle to work across every bottom bracket standard. - Significantly lighter than PFGXP system - Easier installation by allowing you to press the bearing cups into the frame - Easy installation - Two fully sealed cartridge bearings - ISO 4210 compliant. See Declaration of Conformity for details. - BB-frame interface PressFit (Road: 86.5mm) - Crank-BB interface DUB - Bearing type Standard - Spindle diameter DUB - Cup material Steel

- Adapts ISCG-05 mount chainguide arms to fit flange or lockring style bottom brackets

The SRAM DUB bottom bracket series has a simple job—to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Compatible with Cannondale Ai frames - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard

Thread together BB for 386EVO frames and 22/24mm diameter spindle cranks. Machined aluminum cups thread together for stability, increased bearing life, and simple installation and maintenance. No more creaking. Smooth operation. Fast bearing replacement. - Bearings: Enduro ABEC-3 - Bottom Bracket/Frame Interface: BB386EVO, BB392EVO - Bottom Bracket Shell Width (mm): 86mm - 92mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Diameter: 22/24mm - Over Bearing Width: 91.8mm in 86.5mm wide shell - Over Bearing Width Dimensions include supplied silicone dust shields - Weight: 145g Compatible with the following Bottom Bracket Standards (46mm BB shell ID, 86 – 92mm wide BB shell) and 22/24mm diameter spindle cranks: - BB386EVO - BB392EVO

Thread together BB for 386EVO frames and 24mm diameter spindle cranks. Machined aluminum cups thread together for stability, increased bearing life, and simple installation and maintenance. No more creaking. Smooth operation. Fast bearing replacement. - Bearings: Enduro ABEC-3 - Bottom Bracket/Frame Interface: BB386EVO, BB392EVO - Bottom Bracket Shell Width (mm): 86mm - 92mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Diameter: 24mm - Over Bearing Width: 91.5mm in 86.5mm wide shell - Over Bearing Width Dimensions include supplied silicone dust shields - Weight: 133g Compatible with the following Bottom Bracket Standards (46mm BB shell ID, 86 – 92mm wide BB shell) and 24.00mm diameter spindle cranks: - BB386EVO - BB392EVO

Shimano's Ultegra bottom bracket uses Pro Tour-proven technology for lighter weight and super smooth spinning, while still maintaining the same level of durability and stiffness. It's available in English, Italian, or Press Fit models.

T47 threaded BB cups for running 24mm spindle (Shimano, etc.) cranks in T47 frames. Cups have internal bearings and are typically used in BB shells with widths wider than 73mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, or a titanium-compatible anti-seize compound in titanium BB shells. - Bearings: Enduro Angular Contact - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width: 68mm – 132mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Over Bearing Width: 91.7mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 48.5mm x 16-notch

Wheels Mfg BB86/92 thread together bottom bracket for use with 24mm spindle diameter cranksets. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Note: Use only bottom bracket tools compatible with 16-notch, 48.5mm outer diameter cups. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: BB86, BB92 - Bottom Bracket Shell Width (mm): 86mm, 92mm, 89.5mm - Bottom Bracket Shell I.D.: 41mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 106g

High performing square bottom bracket interfaces with English frames. - Fits square-taper spindle cranksets - Alloy adjustable cups - Includes 2 axle bolts

The SRAM DUB bottom bracket series has a simple job- to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard - Significantly lighter than GXP system

BBright is the Cervelo bottom bracket standard found on most of their frames, save the P5. In order to fit Shimano and FSA cranks into this oversized shell, this bottom bracket, complete with CeramicSpeed Bearings, needs to be pressed in. The BBright bottom bracket comes with either CeramicSpeed Standard or Coated Bearings installed. Super smooth, super-round CeramicSpeed Balls contained in hardened-steel races are found on both versions. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. BBright is similar to BB30, but is wider on the non-drive side. As such, the bottom bracket for running 24mm diameter cranks from Shimano, FSA, and others, is unique. The CeramicSpeed Standard Bearings last at least three times longer than other bearings. Thanks goes to hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. These have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to most BBs. The CeramicSpeed Coated Bearings reduce drag by 50% compared to CeramicSpeed Standard Bearings, and show an improvement in bearing life by 60%. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

Chris King ThreadFit 30 bottom brackets are designed and built to be durable, serviceable, and silent. Bearings can be serviced with the Chris King Grease injector tool. - King made-in-house bearings - 5-year warranty - Included Fit Kit #1 is designed to mate the ThreadFit 30 bottom bracket with a DUB MTB 28.99mm spindle - Spindle Interface Type: SRAM DUB - BB Shell Width (mm): 68 , 73 - Bottom Bracket Shell I.D.: 1.37 - BB/Frame Interface: English

Chris King ThreadFit 30 bottom brackets are designed and built to be durable, serviceable, and silent. Bearings can be serviced with the Chris King Grease injector tool. - King made-in-house bearings - 5-year warranty - Included Fit Kit #2 is designed to mate the ThreadFit 30 bottom bracket with a DUB road 28.99mm spindle - Spindle Interface Type: SRAM DUB - BB Shell Width (mm): 68 - Bottom Bracket Shell I.D.: 1.37 - BB/Frame Interface: English

The SRAM DUB bottom bracket series has a simple job—to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard

PF30 Threaded Angular Contact BB for Fat Bike. Fits Specialized Fatboy frames, and any other brand frames with PF30 x 100mm bottom bracket shell. Machined cups thread together for stability, increased bearing life, and simple installation and maintenance. No more creaking. Smooth operation. Fast bearing replacement. - Bearings: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: PF30 - Bottom Bracket Shell Width (mm): 100mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 130g